|
|
|
2-axis BGC Brushless Camera Gimbal GoPro3 Controller PTZ aluminum Full set of parts
Комплект для сборки 2-осевого подвеса на бесколлекторных электромоторах под экшн-камеру GoPro HERO...
|
 |
| в наличии: |
 0 /комплект/ |
|
|
|
Комплект для сборки 2-осевого подвеса на бесколлекторных электромоторах под экшн-камеру GoPro HERO / HERO2 / HERO3 (с моторами и системой стабилизации)
Отлично подходит для установки на квадрокоптер DJI Phantom вместо штатного подвеса
Особенности:
— Простая и легкая алюминиевая конструкция (нерегулируемая предустановленная центровка)
— Прямой привод от моторов
— Антивибрационные демпферы
— Совместим с GoPro HERO / HERO2 / HERO3
— Моторы для БК подвесов 2208, контроллер PTZ, датчик
— Моторы с защитными обоймами
— Масса пустого 230г / 300г с камерой GoPro Hero 3
Комплектация:
100% new Full set of parts
Products include : ( taken in kind, consistent picture ! )
1: CNC aluminum rack * 1
2: Gopro3 tie *1
3: AV damping Ball* 4
4: Install screw*1 ( by default more than one spare screw attention to firmly fight plastic screws installed )
5 : BGC *1 ( the default program for the German V049 professional players can modify their own )
6: 2208 70T motor * 2
All parts Weight: 220 g / 220g
This gimbal controller supported 2-Axis brushless motors and is adjustable, so it can be balanced for camera perfectly.
The original version Brushless Gimbal Controller by Ludwig Färber (Hardware and Software) , Alexander Rehfeldt (Software) and Christian Winkler (Software).
This is an Open Source Project. We add a MOSFET for reverse polarity protection and a status blue LED for status indication.
When you running original firmware (e.g. 049) the LED will show you the startup status.
Hardware Features:
•2-Axis output supported
•ATMega328P microcontroller
•Onboard FT232RL USB-TTL converter
•Input reverse polarity protection
•2~6 cells lipo input
•3 Channels input
•Power and status LED
•Multiport
•UART Port
•MPU6050 6 axis gyro/accel with Motion Processing Unit (IMU board)
•On board logic level converter (IMU board)
•3.3V/500mA LDO voltage regulator (IMU board)
•Dimension: 50mmx50mm
•Height: 11mm
•45x45mm mounting holes
•Weight: 27g (include IMU board)
Cable Description:
German version of the firmware:
Input: A1 is PITCH (pitch) control, A2 is ROLL (roll) control
Back screen "PITCH" position represents the pitch axis output, "ROLL" position shows a cross-roller output
IMU board mounting direction: underside (flat) up, x /-x-axis pointing to the front and rear head direction, y /-y axis pointing to the side of the head
Russian version of the firmware:
Input: A0 is PITCH (pitch) control, A1 is ROLL (roll) control
Back screen "PITCH" position represents the pitch axis output, "ROLL" position shows a cross-roller output
IMU board mounting direction: IC side up (the plane down), y /-y axis pointing to the front and rear head direction, x /-x-axis pointing to the side of the head
Size:
The main control panel: 50 × 50mm Fixed Pitch: 45mm aperture: 3.1mm
IMU board: 13 × 26mm
|
|
|
|
|
|